Underground Mechanized And Mobile Equipment

“GOOD USED - WORK READY” ATLAS COPCO S7D SIMBA LONGHOLE PRODUCTION DRILL RIG

“GOOD USED - WORK READY” ATLAS COPCO S7D SIMBA LONGHOLE PRODUCTION DRILL RIG
Contact Us For Pricing

1 ONLY “GOOD USED - WORK READY” ATLAS COPCO S7D SIMBA LONGHOLE PRODUCTION DRILL RIG

Simba S7 is built on a modern design sharing many components in common with the successful

Boomer S1 face drilling rig. Simba S7 is a long-hole drilling rig for small to medium sized drifts in the 51 to 89 mm hole range.

The rig is capable of ring drilling with parallel holes upward and downward with up to 5,9 m spacing. Equipped with a high-performance

Top-Hammer Rock Drill and boom-mounted drilling unit Simba S7 offers a sustainable high-precision solution for long-hole drilling.

Increased automation lets you add the functionality you need to this versatile rig.

- ONLY 1705 Total Hours on Meter

- Atlas Copco 4 Wheel Drive Articulating Carrier

- ROPS/FOPS Canopy with Operator Screen Protection

- MSHA, CANMET, EPA, CA Approved Deutz D914 Lo4, EPA III, COM III, Tier 3, Stage IIIA, Diesel Engine

- Power Rating at 2,300 rpm; 58 kW (77.8 HP)

- Exhaust Scrubber with Muffler

- Clark Hydrostatic Transmission

- Dana Spicer 112 Axles

- 9:00 R20 Tires Avg. @ 75% NEW

- SAHR Fully Enclosed Wet Multi-Disc (LCB) Service Brakes

- SAHR Spring Applied Hydraulic Released Park/Emergency Brakes

- 24 Volt Electrical System

- Rig Control System (RCS) – versatile and upgradeable to a

higher degree of automation

- Drill settings for up to five different drill bits

- Integrated diagnostic system

- Angle reading instrument

- BUT 32PD Boom

- BMHP 6000 Series Feed

- Feed Extension (with 4′ drill steel).............................. 900 mm

- Boom Extension....................................................... 1,250 mm

- Rotary Acurator BHR 30 for 360º ring drilling

- Rear Stinger

- Stinger Forward on feed ..........................................BSJ 4-45

- Feed Dump, Drilling.............. +24º forward and -79º backward

- Rig Alignment Laser

- Atlas Copco 1838ME Hydraulic Drifter Drill

- Mechanized Rod handling System

- Carousel Rod Handling System, RHS 10............................... 10+1 Total Rods

- Adaptable to R32,TC35, T38, T45 Drill Rods

- Adaptable to 4′, 5′ and 6′ Rods

- Big Hole drilling Kit

- 51–89 (102) mm Hole Diameter

- Mechanized Drilling up to 20 m

- Rock Drill Lubrication Surveillance System

- Total Installed Power.................................................... 80 kW

- Main Motor.................................................................. 75 kW

- Multi-Voltage.................................................................380 to 1,000 Volts

- Multi- Frequency..................................................................50 or 60 Hz

- Transformer.....................................................................5 kVA

- Working Lights Mounted on Roof..................... 35W, 24V HID

- Electronic Overload Protection for Electric Motors

- Digital Volt and Amperage Meter in Electric Cabinet

- Phase Sequence Indicator

- Ground Fault Indicator

- Battery charger

- Auto Retracting Cable Reel c/w Shielded Trailing Cable and Quick Connect Plug

- Hydraulic Driven Atlas Copco LE7 Boost Air Compressor

- Hydraulic Driven Flygt Boost Water Pump

- Approximate Dimensions: 9460 mm Long (Tramming) x 2350 mm Wide x 3050 mm High (with Cab)

- Approximately Weight: 17,800 Kg.

Unit was sparingly used and was parked in Good Working Condition.

Only a New Paint Job and some minor Cosmetic Repairs are required.

Please contact us for pricing, photos and additonal information.


globe